Home/Quality & Standards

Quality is the standard, not the exception.

Every Chibo unit is produced under a fixed verification sequence — document control, 6S workshop discipline, raw-material inspection, in-process control, calibrated testing, non-conformance handling, and final inspection — against named GB and IEC standards.

Certified Standards Matrix

What each code on our nameplate actually governs.

StandardScopeApplies To
ISO 9001Quality management system — process control, documentation, continuous improvementFull manufacturing operation
GB1094.1.2-1996General requirements — power transformersOil-immersed transformer range
GB1094.3-2003Insulation levels, dielectric tests, external clearancesOil-immersed transformer range
GB1094.5-2003Ability to withstand short-circuitOil-immersed transformer range
GB1094.11-2007Dry-type power transformer requirementsCast resin dry-type range
IEC60076 / IEC60076-11-2004International power transformer standard family, incl. dry-typeFull transformer range
GB/T6451-2008Energy-efficiency / loss limits for oil-immersed distribution transformersS11 / S13 / Amorphous series
GB/T17467HV/LV prefabricated substation construction standardYB-series compact substations
Stage-By-Stage Inspection

Four checkpoints, applied to every production order.

Checkpoint · Documentation

Control of Documents & Records

  • System files controlled and managed for the operation of the management system
  • Drawing and specification versions kept consistent with the product on the floor
  • Records maintained as objective evidence that product meets requirements
ISO 9001 documentation control
Checkpoint · Incoming Material

Inspection of Raw Materials

  • Supplier management applied at the point of incoming goods
  • Appearance checking on all incoming material lots
  • Characteristics inspection against the purchasing specification
Supplier & incoming-goods control
Checkpoint · In-Process

Process Control & Dielectric Verification

  • Process inspection performed at each manufacturing step
  • Final inspection confirms each unit's testing complies with the applicable standard
  • Insulation withstand levels (LI / AC ratings) confirmed against GB1094 / IEC60076 before release
GB1094.3-2003 dielectric reference
Checkpoint · Equipment

Calibration of Test Equipment

  • Configuration, calibration, and maintenance of inspection/measuring/test equipment is controlled
  • Calibration cycle managed to keep accuracy consistent with the required measure capacity
  • Equipment use logged to keep results reliable and standard-compliant
Calibrated measurement chain
Process

Treatment of Unqualified Products

  • Clear operating procedure of analysis, processing, and retrospect for deficient purchase
  • Defined handling path for non-conforming product on the line
  • Customer complaints tracked through the same retrospective procedure
Process

Quality Improvement

  • Regular internal management review meetings on quality results
  • Adverse trends identified and corrected in a timely manner
  • Tracking and confirmation built into the review cycle, not a one-off audit
Published Service Promise Matrix

Seven commitments. No fine print.

#CommitmentDetail
1Warranty Period1-year warranty across dry-type, oil-immersed, special transformers, box-type substations, and HV/LV electrical equipment
2In-Warranty FailureFree maintenance or replacement for any failure caused by product quality within the warranty period
324-Hour HotlineHandling response issued within 8 hours of a logged complaint; treatment scheduled at 24h / 48h or a time agreed with the customer
4Outage ResponseOn-site within 24 hours (accessible areas) or 48 hours (remote areas) for any power cut caused by a product contingency
5Lifelong Service PrincipleService continues past warranty expiry on a service-cost-only basis — no re-purchase requirement
6Environmental RecyclingFree recycling and environmentally responsible treatment of scrapped cast-resin transformers
7Technical SupportAccurate, timely response on application conditions, ordering conditions, and design questions across pre-sale, sale, and after-sale stages

Questions on a specific standard or test report?

Our systems engineers can walk through GB1094 / IEC60076 compliance for any unit in the range before you commit to spec.

Request a Quote Call +267 72 247 985